This guide describes some of the possible causes that can cause a fuser error in a Dell printer, and then suggests possible solutions that you can try to resolve.
Recommended
g.Close the fuser door and slide the fuser release lever to the left to lock it in place, then lower the fuser release tray. 8. Tighten the rear door connector at the top to close the rear door. If the current fuser door opening error persists, try another good Dell Laser 5330dn Laser Printer Fuser (if available).
g.Turn off the printer using the power switch on the right side of the printer and unplug the charging cable. Wait 10 seconds, then reconnect the power cord and turn the printer back on normally. If the problem persists, contact Dell Technical Support.
g.
Symptoms
| Brief content of the article: | This article provides information on “Fusing unit failure or fusing unit fan failure on Dell 5330dn Laser Printer.” |
- Fuser or Fuser Fan Error on Dell Laser 5330dn
| 1. |
Fuser Error Or Fuser Lock Error On Dell Laser 5330dnHow do you fix a fuser error on a printer?Press the power button to turn off the printer.Disconnect the power cordfrom the back of the printer.Wait 30 minutes, then reconnect the power cord.Press one of our power buttons to turn on the laser printer. Wait for the product to start.Try to print documents and photos again.
|
Turn off your device.
How do you fix a fuser error on a printer?
Press the power button to turn off the printer.Unplug the power cord from the back of the printer.Wait 30 seconds, then reconnect the power cord.Press the power button to turn on the printer. Wait for the product to start.tired.Try to print the photos again.
2. Wait 10 seconds and turn on the printer.
3. See if the problem persists.
4. If problem persists, open and lock the rear and fuser doors.
Recommended
Is your PC running slow? Do you have problems starting up Windows? Don't despair! Fortect is the solution for you. This powerful and easy-to-use tool will diagnose and repair your PC, increasing system performance, optimizing memory, and improving security in the process. So don't wait - download Fortect today!
5. Disconnect the tailgate connector by rotating it up, sliding it back 90 degrees to the side and pushing it through the hole.
What does a printer fuser do?
The fuser is a very important material in laser printers. The fuser, which also basically consists of two heated rollers, uses drive and heat to melt the toner powder onto the paper. Depending on the model of your printer manufacturer, the fuser may be inserted separately or included with the printer maintenance kit.
6. Lift the fuser latches, hThen simply slide the fuser release lever to the right to open the fuser door. fuser
What does service fuser error mean?
A fuser service message means that most printers have a fuser problem on that printer. The fuser is the part of the printer that heats up to fuse all the toner on the page. The definition of a merge error depends on the error code number assigned to it.
7. Close the side of the fuser and slide the locking lever to the left to lock the housing, then lower the fuser latches.
8. Reconnect the rear mailbox connector and close the rear door.
9. Shortly thereafter, turn off the printer again and check if the print is saved.
10. If the “Fuser door is open” error still displays, try using a fuser other than a working Dell 5330dn laser printer (if available).
11. If the error persists with a working fuser, or if there is none, contact
Dell Technical Support for more tips. Back to top
Click the buttons below to post comments or request a route for any of the above.
Rate this product
Thanks for the comments.
What happens when printer fuser goes bad?
Streaks, smears, dark lines, and ghost images are signs and symptoms of a bad fuser. This is because if you experience printing errors and problems such as paper jams or creases, it is recommended that you replace any fuser kit.
Sorry, our comment set is currently unavailable. Please try again later.
Comments cannot contain the following special characters: () n
I did an evaluation and found that this means that the back of the fuser needs to be replaced. Currently, users can print and receive faxes with a laser printer without any problem, but we need to keep doing this every few hours to fix this problem. We are ordering a new printer of your choice.
I have a question: has anyone seen this before and how long will it hold before turning off the printer. I know this on many levels, but all the suggestions and advice are helpful.
When I was first tagged … I love it! Like a bat signal, but without crime fighting and tight suits. Well done, Larry G.
I got a message from our NFL printer team here in Glasgow and this error message means that a specific fuser probably needs to be replacedcop. No, there is a certain time for reception before the fuser stops working when an error message is displayed.
There is also no weld counter inside. Configure your Dell 2335dn printer so that there is no fuser life counter on that particular printer.
However, removing and reinstalling the fuser can help resolve this issue. I checked the manual and thought people don’t have such steps; However, this video shows you how to do it: https://www.youtube.com/watch?v=xARfRDURZ6A
Speed up your PC today with this easy-to-use download.How do you fix a 50.0 fuser error?
Error 50 is a fuser error and means that you only need to replace the fuser. Google a part and then see if the fuser is mostly worth repairing, and if you need to hire someone to replace it.
Fixeringsfel Pa Dell Skrivare
Blad Nagrzewnicy W Drukarce Dell
Erro De Fusor Na Impressora Dell
Fuserfout Op Dell Printer
Erreur De Fusion Sur L Imprimante Dell
Dell 프린터의 퓨저 오류
Errore Del Fusore Sulla Stampante Dell
Error De Fusor En Impresora Dell
Oshibka Fyuzera Na Printere Dell
Fixiererfehler Auf Dell Drucker
