You may encounter an error code indicating installshield result code = -12. There are several steps you can take to fix this problem. We are talking about this now.
Recommended
This article describes some workarounds for pa real error RESULTCODE = -12, which may occur.
SOLUTION is individual: if you do not have enough disk space, you will get a working RESULTCODE -12.
SOLUTION 2: Result code -12 may be displayed if the entire unattended installation does not use the same sequence of dialogs that no doubt does when installing the model, or if a remarkable error causes the installation to stop. The line must be canceled.
In the SETUP.ISS section, [DlgOrder] of the utilities must differ from the following:
[DlgOrder]
Dlg0 = Welcome Dialog-0
Count = 9
Dlg1 = SerialControlNumber Dialog-0
Dlg2 = TargetDirectory Dialog-0
Dlg3 = UserInstallationType Dialog-0
Dlg4 = SdSelectFolder- 0
Dlg5 = LanguageChoice Dialog-0
Dlg6 = International Settings Dialog -0
Dlg7 = SdShowInfoList-0
Dlg8 = RebootDialog-0
However, if Count = 10 and additional line Dlg2 = MessageBox-0, it can be either:
– Wrong sequence / control buttons.
– An additional dialog box appeared during this recording session.
Exit. Proceed as follows:
1) Make sure the serial number and codes match those shown on the green product cards. They are always displayed in [di In the SerialControlNumber-0 section log window] as follows:
Recommended
Is your PC running slow? Do you have problems starting up Windows? Don't despair! Fortect is the solution for you. This powerful and easy-to-use tool will diagnose and repair your PC, increasing system performance, optimizing memory, and improving security in the process. So don't wait - download Fortect today!
[Dialog SerialControlNumber-0]
nvCount = 1
svSerialNumber-0 = 123456789
svControlNumber_1 -0 = ABCDE1
svControlNumber_2 -0 = FGHI2
svControlNumber_3-0 = LMNO3
2) If the types are correct, remove the raised line “Dlg2 = MessageBox-0”.
3) Enter number = 9 and renumber the lines throughout the [DlgOrder] session. Most likely, a hibernation occurred during the session recording, or this additional recording was placed in the setup.iss file.
SOLUTION Three main ones: In Progress 9 Installation, auto-hardening Make sure that the setup.exe database does not actually reference UNC files. Map a drive on your home installation computer to the directory where the Progress installer actually resides. Also in OpenEdge 10, make sure all paths are UNC paths or only all mapped paths are disks, and do not use dashes in course names or ini dispatch names.
Example:
UNC: anypc 91D setup.exe -s -f1 … -f2 …
Assigned to: T: setup.exe -s -f1 … -f2 …
InstallShield Silent (ISS) allows silent or batch installations by writing market install information to a response file that can then be run with the -s direction parameter.
This article describes some workarounds for the RESULTCODE = -12 error, which can also occur.
SOLUTION 1. If you don’t have enough disk space, you can get RESULTCODE -12,2:
A RESULTCODE solution of -12 may be displayed ahead of time if an automatic installation is in progress, the same selection dialog is not used as for model installation, or if an error could interrupt a market installation.
IN SETUP. [DlgOrder] iss, utility information, you should see the following entries:
That Count = 10 and an additional call to Dlg2 = MessageBox-0 could be like this:
– Serial / control buttons must be wrong.
– An additional dialog appears during a recording session.
1) Verify batch and control instructions match those accompanying the green product sheets. They are in the [SerialControlNumber Dialog-0] and look like this:
2) If yes, remove the extra line after “Dlg2 = MessageBox-0”.
3) Set count = 9 and then renumber the lines in the [DlgOrder] training session. Most likely, a warning appeared during the recording of the session, as a result of which all additional recordings were saved in the setup.iss file.
SOLUTION 3: In Progress 9 Background installation Make sure the UNC file references do not point to the second setup.exe. Place the disk on your local installation disk in the directory where the Progress installer is located. In OpenEdge 10, make sure all sidewalks are UNC paths or that all mapped streets are disks and cannot use dashes in path names, possibly in an INI file name.
SOLUTION 4. Verify that the primary web server installation directory (if applicable) is correct for the [WebServer Dialog-0] section. Take a look at the _szCGIScriptDir and _szDocRootDir entries.
Speed up your PC today with this easy-to-use download.
Installshield Resultcode 12
Codice Risultato Installshield 12
Installshield Resultaatcode 12
Code De Resultat Installshield 12
Installshield Resultcode 12
Installshield 결과 코드 12
Installshield Resultcode 12
Installshield Resultcode 12
Kod Wyniku Installshield 12
Codigo De Resultado De Installshield 12
