What is the problem with the Dell Optiplex 760?

It looks like the problem is that there is NO DISPLAY. However, since these are USFF devices, there are NO OPTIONS other than the built-in DVI display. Tried different sockets, cables and monitors. No help.

Where does the error code on a Dell laptop come from?

The term blue screen error usually comes from the occurrence of these errors. These error codes are usually generated with “STOP 0xXXXXXXXX” (X stands for various alphabetic and numeric codes that indicate the cause of each of our errors.

Dell Gx755 Error - Tommy's Computer Blog

Table of Contents

If you’re having Dell error gx755, this guide should help you.

1. When the satellite power supply is connected to the source, the technology starts a self-test (POST). At this point, LEDs 3 will light up and the remaining time is 4, and the computer fan will run at full power continuously. When I press the stamina button, nothing happens. When I hold it down, the computer shuts down, then turns back on, and the same problem occurs by itself. (See Tones 1 through 4)

2. The fan speed increases in real time. If I quickly unplug the power cord and plug it back in, I would say that the computer will automatically check Windows and computer Lies normally.

3. When I restart a specific computer after preinstalling Windows, it usually goes through an automatic check.

4. If I turn off my computer, I say Windows will shut down, but not the electronic computer. The green bezel provides power to the control-panel LED while the power supply and device fan remain on.

Note. All 1: memory and slot tests have already been performed, and no problems have been identified yet. 2:

Note. If I do not install memory in the slots, this special beep sounds when the fan does not start.

Note 3: If I try to install a computer with the processor socket disconnected, POST will be aborted quickly and the computer may shut down.

Note 4: If, in addition to disconnecting the processor power connector, if the processor fan connector is disconnected, POST will abruptly stop, but the computer will restart without interruption.

Does anyone have any specific advice on this? I don’t understand what I’m doing anymore.

One nWhen I was in the Optiplex 755 my g / f was good, then when she used to press the start button, the flashing yellow contact came on, so she waited 10-15 minutes for your lover’s desktop to look normal, later the wife turned off the PC the next day something happened the same, but unfortunately it took 25-30 minutes to view the desktop when the green start button was pressed, the green light of the person was still blinking, so they hadn’t been on the PC for the past few days transferring their files to the removable drive.

Number 2 appears on your PC desktop, and the green start button is definitely green. Now she’s concerned that this tool might not show up again if it turns off the desktop, so I can’t tell you what appears to be affected. When it booted, it never installed a PCI card or configured anything

Hope to find a solution to your problem and that this is not your friend’s motherboard!

Symptoms

Reason

Solution

Error starting diagnostics.
Error Resolution

1. Error While Executing Diagnostics

Some OptiPlex 755 systems may cause the error listed in the Diagnostics section below.

msg UC 0 : There were no exceptions to general politics on voter balance sheet 18. Physical offset 37a18 4DA8 mapping file counterweight

2. Error While Resolving The Error

To resolve this issue, update your system BIOS to the latest version.

Go to the support site, use your options to select the model for your system by performing a one-time auto-discovery using a service tag or a single tag that you can select from a list. Then select Drivers and Downloads from that menu.

Run diagnostics again and verify that the error is no longer displayed.

Rate this article

this is

Thanks to the plastic bottles for the comments.

Sorry, our systemcollecting reviews is currently unavailable. Try again.

Comments should not contain special characters: () n

Is your PC running slow? Do you have problems starting up Windows? Don't despair! Fortect is the solution for you. This powerful and easy-to-use tool will diagnose and repair your PC, increasing system performance, optimizing memory, and improving security in the process. So don't wait - download Fortect today!

1. Download Fortect

2. Follow the on-screen instructions to run a scan

3. Restart your computer and wait for it to finish running the scan, then follow the on-screen instructions again to remove any viruses found by scanning your computer with Fortect