If you are experiencing the Seagate 7200.11 bsy error, this user guide should help you.
Recommended
g.There are two common errors typical of Seagate 7200.11 hard drives (caused by firmware errors): – LBA error: This happens when your company’s BIOS can recognize your hard drive on POST, but as a 0 MB drive. – BSY error: Occurs when your hard drive enters the off state or B u SY state. In this state, your real hard drive will not be recognized by the BIOS during POST.
Please note: This post may not be for everyone. HD is not hard to kill unless you follow the instructions with extreme care. I am NOT responsible for any damage that may result in data loss (no one has lost anything yet, but unfortunately, accidents can happen).
There are two common errors (caused by firmware errors) on Seagate 7200.11 hard drives:
– 0 LBA error: Occurs when the BIOS can recognize the hard drive during POST, but as a 0 MB drive.
– BSY error: If your company’s hard drive goes into shutdown or BuSY state. In this state, your hard drive will not be recognized by the BIOS during POST.
There is an issue that can cause Seagate hard drives to fail immediately after being turned on. Once this condition occurs, most drives cannot be normalized without Seagate intervention. Data that the disk will and will remain unchanged will become available after normal operation is restored. This is usually caused by a firmware issue related to a specific manufacturing process.
This is a state This was caused by a serious firmware issue that put the drive’s fault log in an invalid location, making the drive inaccessible.
A Firmware Incident, which is the Event Log Cycle Load End Limit (320), was not set correctly. When the log event is initialized, the boundary condition that would normally determine the end of the log event is offset by one. If the event log counter is at input 330 or a multiple (320 + x * 256) during startup and if a specific message pattern (depending on the type of tester used during the production test process) was present through the reserved area the system monitors if the file system the reserved area of the disk was undoubtedly collected during production, the firmware will grow as the event log pointer moves beyond the creation portion of the event log data. This error is detected and affects the “confirmation failure” that triggers the disk lock.because you are just doing a safe action. If the train enters a stable carriage, further updates are made so that this counter becomes impossible and the train remains for subsequent service periods. The problem only occurs if the loop initialization is assigned when the value of this event log is 320 and / or possibly a multiple of 256 thereafter. When the drive is in this state, it is not possible to fix / restore existing failed drives without advanced Seagate intervention. For a drive to be affected by this issue, the firmware must contain the issue and go through a specific build process.
Recommended
Is your PC running slow? Do you have problems starting up Windows? Don't despair! Fortect is the solution for you. This powerful and easy-to-use tool will diagnose and repair your PC, increasing system performance, optimizing memory, and improving security in the process. So don't wait - download Fortect today!
Seagate has implemented containment measures to ensure that all production trials record the same gentle filling process. This change is an integral part of the verification process. All hard drives manufactured on January 12, 2009 and later are affected by this issue as these items have gone through a corrected overhaul process.
Seagate Clients It is highly recommended that you update the firmware of all affected drives to the latest version in advance. If you experience this issue, or if the episode in question exhibits this behavior, please contact the most appropriate Seagate representative. If you want efficient access to the data you need to solve this problem, Seagate offers free data recovery services. Seagate will likely be working with you shortly to minimize inconvenience to you or your business.
or (buy a dedicated RS232-TTL adapter, FT232BM / BL, and both are not needed!)
– 1 (one) FT232BM / BL adapter (see below) and USB TV cable ($ 12.47):
Any other similar adapter will work, just switch to + 3.3V DC (+ 5V will also work, but I recommend 3.0-3.3V). You can also find USB to TTL adapters that use USB to RS232 internally and then read to TTL. For example, some people have used a PC cellular data cable (many use RS232 to TTL).
– 1 (one) set of ten 5-inch jumpers and 20 connectors ($ 5):
– 1 (odyn) a computer with terminal software (eg HyperTerminal or similar) plus an RS232 or USB port.
– Corrected Seagate Firmware (Released January 22, 2009 and January 24, 2009 for all affected drives).
Connect the RS232 TX and RX networks using a TLL adapter, for this you may need something like jumpers or solder directly to the PCB. Connect GND and + 5V of the PC to an electromechanical power supply or similar. Please note that they come directly from Seagate sites, so you should interact as follows:
You can use the RED cable (+ 5V) from the PC power supply. Black GND is (yellow is actually + 12V, so don’t use it).
If you don’t want to interrupt the pressure supply, just use a CR2032 (3V) battery:
Basic configuration idea (I also used USB-to-RS232):
Set the RS232 port to: 38400 multiple N 1 (for example this one):
To get LBA 0 error, you need to do a quick format to regenerate a partition that only has m0,2,2, and the rest can be left blank if desired by putting single ones commas or by adding zeros. After all, you should use the “ValidKey” code along the way, or just 22.
Warning: the commands used must be 100% identical to those presented here, incorrect command commands can lead to data loss and / or possible loss of hard disk! Double or double check your cmd before hitting Enter!
F3 T> m0,2,2,0,0,0,0,22 (input)
Level T ‘m’: Rev 0001.0000, Flash, FormatPartition, m [Partition], [FormatOpts], [DefectListOpts], [MaxWrRetryCnt], [MaxRdRetryCnt], [MaxEccTLevel], [MaxCertifyTrkRidKey], [Val ]]]
Now wait 15-30 seconds until something like this appears (it may be slightly different):
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewrite Retries = 0000User partition format 5% complete, Zone 00, Pass 00, LBA 00008DED, ErrCode 00000080, Elapsed time 0 min. 05 sec.
User section formatted successfully - Elapsed time 0 min. 05 sec.
ONLY message as above, you can turn everything off.
Fix BSY or CC errors, also called BUSY.
First of all, make sure you are not at home; on a table with free access to the player is best.
Secondly, you wellremove the printed circuit board (PCB) from the HDA housing using a mini Torx 6 screwdriver.
Third, connect the RX and TX cables of your RS-232 adapter, make sure everything is probably correct, then connect our power supply to the standard hard drive board.
Explanation: The problem with driving is that the drive might get stuck in a BUSY state. This basically blocks the SATA port which is important for the BIOS issue (cannot detect this particular drive on POST). You can see this sorting by mistake in the port (LED: 000000CC FAddr: 0024A051). As soon as you see this in the terminal, your travel session will be completely blocked and orders will no longer be accepted. To work around this issue, we need to make sure that you separate the PCB from the hard drive enclosure so that most of the LEDs sold: 000000CC FAddr: 0024A051 cannot be sent to the terminal session firmware.
After connecting power to the signal board, press CTRL + Z in the HyperTerminal session. You should now see a new prompt like this:
F3 You t>
If you don’t see this message, check someone else’s RS-232 connectionsto the player. (You should have swapped TX and RX).
F3 T> / 2 (enter)F3 2>
F3 2> Z (Enter)Rotation completed
Elapsed time 0.147 ms (precious time changes here)
F3 2>
And now the most difficult thing in a person. Exercise a lot to gain strength before you even try. You have to make sure the screws don’t touch the whole PCB where they won’t be trusted, otherwise you will fry the board. If you’ve been exercising for a while and the power isn’t just plugged in, start with STEP ONE.
With the human connected, connecting the card and TX / RX device cables, assemble the card through the HDA unit. You must be online if you do.
F3 2> U (enter)
F3 2> / 1 (enter)
F3 (enter)
First, skip step 1> n1 in list G. If the disk still freezes due to a BSY error while doing full BSY fix, you will need to repeat the BSY process to get the G-List below.
p>
F3 1> / T (enter)F3 T> i4,1,22 (enter)
Level T ‘i’: ed. 0001.0000, Overlay, InitDefectList, i [DefectListSelect], [saveListOpt], [ValidKey]
F3 T> m0,2,2 ,,,,, 22 (enter)
Level T ‘m’: Rev 0001.0000, Flash, FormatPartition, m [Partition], [FormatOpts], [DefectListOpts], [MaxWrRetryCnt], [MaxRdRetryCnt], [MaxEccTLevel], [MaxCertifyTrkRewrites], [ValidKey]]]
Max Wr Retries = 50, Max Rd Retries = 00, Max ECC = t-level 14, Max Certify Rewrite Retries = 00C8Custom partition format 10% complete, zone 00, pass double zero, LBA 00004339, ErrCode 00000080, elapsed time 0 min. 05 sec.
The format of the user section is successful - the elapsed time is 0 minutes. 05 sec.
If you haven’t received all of the above messages, then you have missed something important, and shutting down your hard drive will result in an unreadable burst of messages, so be careful.
ONLY after the topic as above, you can turn everything off.
Remember that I have worked hard to put all this knowledge together and provide more and more useful details.
If you experience any of the following problems, first read the Seagate Barracuda 7200.11 READ_ME_FIRST!
Speed up your PC today with this easy-to-use download.
Seagate 7200 11 Errore Bsy
Seagate 7200 11 Bsy Fout
Oshibka Seagate 7200 11 Bsy
Seagate 7200 11 Erreur Bsy
Error De Seagate 7200 11 Bsy
Seagate 7200 11 Bsy 오류
Seagate 7200 11 Bsy Fehler
Erro Seagate 7200 11 Bsy
