Hp 4200 60.2 Error - Tommy's Computer Blog

Table of Contents

Sometimes your system may display the hp 4200 60.2 error message. This problem can be caused by a number of reasons. g.Error 60.2 means that the tray was not raised correctly and the paper sensor has not been activated within a certain amount of time. At this point, you usually hear an exaggerated squeak or click first, and then error messages. Error 60.2 Tray Boost is usually caused by improper paper loading.

Error Code 60.2 – Normal Ignore HP Laser Printers. This Error Can Be Quite Persistent After Turning The Printer Off And On Again. It Can Be Found In Many Popular Products, Including The Following Types:

4200 4300 4250 4350
M601 M602 M603
M604 M605 M606

Why do I get a 60.2 error on my HP printer?

Error code 60.2 is common with HP laser printers. This error can potentially be quite persistent, even if the printer is cycling. It is found on more and more popular models, including the following types; This means Tray 2 and its escalator motor will not work. Do you hear a knock or a knock? This usually happens with an error of 60.2.

This means Tray 2 and its elevator motor are not working. Can you hear pulsating clicks? This is also the case for any type of 60.2 error.

Follow these steps to diagnose error 60.2 rules and resolve the issue.

1. If your site has not already done so, immediately turn off the printer and then turn it back on. If error 60.2 applies to TVs, always turn off the printer and leave it off. Check which experts state that Platform 2 Lift definitely sits in the CC PCA (item J93).

2. Remove h. P. Kassets for paper for a laser printer. 3. Check the gear on the right cassette door. Try changing the time for a full shift and see if the dish rises. If this mechanism works correctly, go to step 4.

What’s the repair code for a hp 4200 printer?

LaserJet 4200/4300, HP 4250/4350 Lift Motor Failure Repair 60.2, 60.3, 60.4, but 60.5 in Southern California! HP LaserJet 60.02 printer error code recovery in Los Angeles and Orange County.

4. Turn on the HP laser printer to activate the paper cassette-sized wireless home alarm and see if the elevator turns. If it does not rotate and / or makes strange noises, you will need to replace the lift unit and possibly the motor.

5. If it rotates with the size sensors pressed, click on the paper visibility flag to see if it surrenders. If this continues, owners will need to inspect the receivers.

6. If 60.Error 2 signal persists, you will need to replace the CC PCA when you need to replace it.

How do I fix error 6002 on my printer?

I solved this problem by loosening the paper in the magazine slot. If the paper is too tight, the printer will spit out error 60.02 as well. Adjust our slider in the paper tray so that there is a slight gap again.

(Use these symptoms to solve the problem)60.X Error (X indicates which container is 1, 3 or 4. -) Indicates an error while lifting the container, followed by one of the following symptoms:1. Loud bell or pop – from the attack zone of the tablet. Typically, when typing, it is definedamount of paper (more than 400).2. Clicks due to engine bay installation – rotates, only the paper level indicator does not move. Jumping continues for 12 seconds, then part of the error is displayed. The symptom is usually erratic and impossible, except for a small amount of paper and results in a 60.X error.3. When the tray is inserted, there will be a loud popping sound followed by an indication of how the paper on the display moves with the paper in the tray to its full position, regardless of the amount. Is accompanied by errors 13.X or 60.X.4. The elevator cannot start the engine; lifting does not occur if error 60.X follows.

problem:Tablet design problemOccurs when more than 400 sheets of paper are loaded in the paper tray, but the tray rises when returned (due to excessive load lifting the tray). This causes the gears to jump, plus a click noise and a 60.X error. Install a new location in the paper tray) version 4250. There are 3 tabs on the right side of the table guides to resolve this issue.

Pickup releasedIs it a jack, a gear, or both.They sit in the mounting slot, which leads to loosening of the assembly.

Defective container lifter motor bracket.The engine gear is not engaging with the drive sprocket, which prevents the chainring from lifting and causes the correct 60.X error. This is due to the curved metal joining the plastic piece that attaches your current bed’s elevator motor to the frame. Sometimes this metal is considered bent (it should be at an angle of 90 degrees from the frame). The situation is made worse when there is indeed a lot of paper in the actual tray, and this can work well with a small amount of paper.

Faulty elevator motorA stroke failure that does not result in a stroke normally associated with paper in the tray.

Resolution: Symptom # 1 – Replace the paper tray with another paper tray. Ribs have now been added to the tray when the side guide is on the right to reduce tray movement (reduce tray movement before 400 or more pages are loaded at one time). In addition, the gearbox must be raised to improve the performance Act between the sprocket and the gearbox lift drive of the vehicle (raised by about 0.3 mm).

Symptom # 2 > Remove the paper tray and try moving the elevator drive from side to side while you are still in front of it. If it slips back and forth again, check the position of the motor. It should be at this 90 ° angle and may need to be bent to fix it. The Drive Improve assembly must be removed to complete the repair.

Feature # 3 – Pull the hopper input shaft to the left. If it falls, then the drive is missing a slot and / or a gear wheel for receiving paper documents. In addition, the chuck base bushing and 18T gearbox may need to be replaced. If the channel does not fail, go to the next step.

About MetrofuserMetrofuser is a leading global designer, innovator and distributor of printer parts, hardware, diagnostics, repair and system solutions for mission-critical business users. Products and services include laser remanufactured parts, printer remanufactureds-printers and service training for HP, Lexmark and Canon brands. Client organizations include office equipment distributors, online distributors, spas and MPS service providers nationwide. Metrofuser was named by Inc. fastest growing company for five consecutive years. For more information see http://www.metrofuser.com .

Is your PC running slow? Do you have problems starting up Windows? Don't despair! Fortect is the solution for you. This powerful and easy-to-use tool will diagnose and repair your PC, increasing system performance, optimizing memory, and improving security in the process. So don't wait - download Fortect today!

1. Download Fortect

2. Follow the on-screen instructions to run a scan

3. Restart your computer and wait for it to finish running the scan, then follow the on-screen instructions again to remove any viruses found by scanning your computer with Fortect